Ring Security Cameras
Floodlight Cam Lights coming on constantly
I just got and installed my first of two Floodlight cams. When I got home last night I found the light was on so I turned it off manually. The light cam back on in a few seconds. I turned it off again and it did the same thing. So, I left it by itself and it turned on then off for a few seconds and back on constantly. I checked to see if there were any alerts and there was nothing noted. My wife told me that it was doing it all night. I ended up turning the whole camera off for the night. Any ideas? I checked and I don't have a schedule and as I have stated I don't have any alerts. I turned it back on this morning and so far the light hasn't come on.
88671 •
5 •
98 •
06-10-2019 06:43:54
Responses (24)
- M
Kjohnrussell, When did you get your new floodlight camera? This past Thursday I installed 2 replacement floodlight cameras that had manufacture dates of October 2019. What I finally figured out on Friday night is that both floodlight cameras keep automatically turning on the floodlights (not the cameras just the lights) every 30 minutes on the dot all night long. There is nothing outside that is triggering this. Are your cameras doing something similar? I've spent the last four days trying to first figure out what was happening and troubleshoot myself, then on the phone with ring support for hours. They haven't been able to figure it out, and they say that I'm the only one having this problem.... Please let me know if you're having the same issue!
•5
18-11-2019 03:21:14
KIt is a new device, purchased about one-two months ago. Personally, I think the passive infrared (PIR) is defective on these newer versions of the floodlight cams is defective (or something). That said, if you go into Device Settings | Light Settings | Motion Zones for Lights -- this is where you can set the distance for motion sensing. This is what controls when the light comes on, not motion but PIR. I have been slowly turning this to shorter and shorter distances and that SEEMS to help, but it's hard to say. I have mine set almost to min but my light is still going on periodically. Just to be clear, the light sensor is NOT tied to the motion sensor. You can (as I have done) keep the motion sensitivity turned to whatever level you would like. The motion sensor is what triggers recording - lights or not. Let me know if that helps you.
•4
18-11-2019 11:56:21
RI had to turn the zone down for the light to the minimum setting. It still turns on once in a while but not nearly as much as before. Anything higher than minimum it would still happen too frequently.
•1
18-11-2019 12:48:22
M@kjohnrussell Thanks for your reply. I also thought from the very beginning that it's a bad batch of floodlight cams. Hopefully, it will help if they see that I am not the only one with these issues. There is another discussusion that I found last night of the exact same issue, and I've posted some replies there and have sent the link to the level 2 that is working on this. [https://community.ring.com/t5/Security-Cams/floodlight-cam-lights-go-on-every-30-mins-for-about-20-secs/td-p/5655](https://community.ring.com/t5/Security-Cams/floodlight-cam-lights-go-on-every-30-mins-for-about-20-secs/td-p/5655) After calling Ring support several times over a couple days, I was able to speak directly with a Level 2 on Saturday night, and we spent about 2 hours troubleshooting and running various tests. He escalated (to software engineers). What has been determined is 1) It is NOT related to the sensitivity (distance) setting in the light settings. Thus not related to external motion triggers. I am glad that you have also tested and noted that this is not the issues. This has been tested more than three times by me and then by Ring several times now. They need to stop trying to test this, as it is a waste of time. Plus, reducing the functionality of the lights would not be an acceptable solution, as then an intruder would practically be in your house by the time the lights turn on. There would be no light deterrent and little hope that you get a decent picture of the intruder. 2) It is not due to electrical issues. 3) Neither of my floodlight cameras are able to update the firmware, even through a cellphone hotspot. What is the firmware version for your floodlight(s)? Can you please post your replies to the other thread? I think it would help if Ring saw in one posting that many people are having this issue. Thanks. [https://community.ring.com/t5/Security-Cams/floodlight-cam-lights-go-on-every-30-mins-for-about-20-secs/td-p/5655](https://community.ring.com/t5/Security-Cams/floodlight-cam-lights-go-on-every-30-mins-for-about-20-secs/td-p/5655) > @kjohnrussell wrote: > > It is a new device, purchased about one-two months ago. Personally, I think the passive infrared (PIR) is defective on these newer versions of the floodlight cams is defective (or something). > > > > That said, if you go into Device Settings | Light Settings | Motion Zones for Lights -- this is where you can set the distance for motion sensing. This is what controls when the light comes on, not motion but PIR. I have been slowly turning this to shorter and shorter distances and that SEEMS to help, but it's hard to say. I have mine set almost to min but my light is still going on periodically. > > > > Just to be clear, the light sensor is NOT tied to the motion sensor. You can (as I have done) keep the motion sensitivity turned to whatever level you would like. The motion sensor is what triggers recording - lights or not. > > > > Let me know if that helps you.
•5
18-11-2019 03:23:55
M@rwheelwright Thanks for your reply. Our lights are going on exactly every 30 minutes, and turning down the sensitivity has not stopped it. I would also be concerned that turning the light senstivity down makes the security camera ineffective at night, as the lights wouldn't go on until the intruder is under the lights, already in your home, or never (depending on where the lights are positioned).... In my first set of floodlight cams, when it was windy and branches moved, I had to turn off two of the three pre-setzones. It would be helpful if the light settings had more options and precision.... > @rwheelwright wrote: > > I had to turn the zone down for the light to the minimum setting. It still turns on once in a while but not nearly as much as before. Anything higher than minimum it would still happen too frequently.
•1
18-11-2019 03:33:29
- B
Anyone ever find a solution for this? Mine is constantly turning off and on still all night.
•4
24-04-2020 02:59:30
•
LI changed the sensor area to eliminate coverage of the air conditioner, and that worked for me. It seems the motion sensor was picking up on the fan blades being turned by the wind, even when the AC unit was not working.
•1
24-04-2020 11:37:43
RI also have had the problem with my floodlight cam light constantly turning off and on. After reading this forum, I agree with LeeA. Just to the left of my floodlight cam, I have a window AC unit, that is for my closed-in patio, and I had it running. After reading LeeA's post, I turned that A/C unit off, and my light ceased to cycle. This camera is on the same electric circuit as the floodlight cam, but it also is close to the floodlight cam. So, I don't know which was contributing to the on/off sequence of the light, being on the same electric circuit or picking up some "signal" from the A/C unit, but turning the A/C unit off worked. Hope this helps.
•0
30-04-2020 02:20:46
RUnbelievable. alllll the functionality and a super simple button to TURN OFF THE LIGHTS NO MATER WHAT does not exist.. You guys succeed so well at so much of this. But this a HUGE FAIL.. so I have flood lights in my back yard but if I want to hang out at night . I have to way of easily and consistently keeping the extremely bright light from coming on.. so ridiculous.
•6
30-04-2020 03:44:19
NJust installed one on my front drive. Having same problem. I adjusted the light zones to nearly minimum and that seemed to bring the constant on and off to a minimum . I then went outside to see how close i had to get to have the lights turn on and i had to get to within 7 ft. Completely useless as a floodlight. I will be doing more adjustments over this weekend to see if i can find a useable solution.
•3
07-06-2020 02:12:40
- Z
Same. Installed yesterday and the light does not turn off Overnight despite all settings adjustments. Wish I saw the forum before I bought. Will be returning.
•0
13-06-2020 04:21:27
•
- A
I'm having the same issue. The first month I had it, all was well. Now, the lights keep coming on even throughout the day. I've tried everything, all the suggestions here and still coming on. Can I return it for a new one? I've had to turn it off because it's irritating the neighbors...and me! The one in the backyard, purchased at the same time, is working perfectly.
•0
17-06-2020 12:09:56
•
- A
So does anyone know if there is a fix for this. Because now I have to turn my security camera off every night before the bloke behind me beats my head in because this stupid lights is constantly shines in his liverroom window. What a waste of £250. New I should of stuck to swann cctv
•0
27-06-2020 10:04:11
•
HSame here. Just started happening a few weeks ago. I updated the firmware still the same problem. Sucks
•0
27-06-2020 11:08:38
DJust bought two today. Lights just keep going on right after they shut off. I had to adjust to minimum, but now I have to be nearly under the unit to get the light to turn on
•0
05-07-2020 02:10:42
BI'm also experiencing the same issue. Noticed it a while ago but as the floodlight is on the side of the house with only bathroom windows I don't see it often. Sometimes the light goes back on every 3 or 4 seconds after it's just timed out. Luckily only my neighbours gardens are affected but this is pretty poor! I've reduced the distance to minimum and like everyone else I have no motion detected, nothing visible on camera but it still goes off! Terrible!!
•0
05-07-2020 11:45:41
JSame here. Just purchased direct from Ring a few days ago. Lights going on and no events or indication as to why. Turned the light zones to minimum. Any updates on this?
•0
09-07-2020 06:35:02
RSame problem where randomly lights turn on. Installed last summer have had continious problem with lights randomly turning on. Lately (after firmware update?) random turn on seems to be better as the lights turn on maybe three or four times per night compared to before lights would turn on 10-15-20 times per night. There now apprears to be a delay of 1-2 seconds after motion is detected before lights turn on. Still not right but at least tolerable.
•0
09-07-2020 02:24:55
Didn't find an answer ?
Log in or create your Ring account to post a question and join in the on the conversation.
Community Resources
©2024 Ring LLC or its affiliates
kjohnrussell
I have the same problem. I have a several spotlight cams (purchased a year ago) that work perfectly! I added a new one to my set and the newer one has the PIR and the light is going on constantly! Based on this thread, I've turned the light sensor down pretty low (but I like the motion sensor up to capture any activity). I'll watch it tonight to see if turning down the light sensor helps.
2
15-11-2019 07:49:40
•