Please support / update the ring doorbell (especially Doorbell 2) product in the app to allow snapshot captures every 1 minute (especially if you are hardwired) or have good solar similar to the settings available in Ring Stick Up Cam Elite/Wired. There is no reason it can't support this if it is hardwired in terms of power. Every 5 minutes is too long.

Well . . . I had the "30-seconds" option available before for Snapshots, but now it's gone, and the shortest I have is the "5 minute" option. Apparently they are going in the opposite direction away from your "5-second" or "1 second" suggestion. I have 3 Stick-up Cam plug-in (all Gen 2), and all mounted outside, and all set at "Frequent" on their Motion Frequency. All 3 of them had the "Snapshot Capture" activated, all with 4 available choices for "Snapshot Frequency" of; -- Every 30-seconds. -- Every 1 hour. -- Every 14 minutes -- Every 5 minutes. All 3 Cams were operating fine on "Every 30 seconds" option and were providing a Snap every 30 seconds. Then one Stick-up Cam kept having issues going "Live View" ... not connecting ... better described as "never connecting". I tried several recommended trouble-shooting solutions that did not help. I eventually tried "Factory Reseting" this cam (holding the orange button for 20+ seconds) and removed the cam off my android phone app, and then went through the entire set-up procedures again. It's been only a few days now, and the reset Cam can do "Live View" again .... BUT ... when it seems that this Cam updated it's firmware (during the set up process), it now only has 3 available choices for "Snapshot Frequency" of; -- Every 1 hour. -- Every 14 minutes -- Every 5 minutes. I lost the "30-second" option! For my purposes, a single 'snap' every hour, or 14 mintues, or even every 5 minutes is pretty much useless ... cool to playback and watch ... but not useful for security purposes. Why even have the "1 hour" option at all on a Security Camera? The "30 seconds" option was the closest thing to continuous recording and I found it extremely valuable to catch stuff that occurred between motion-activation events, or activities that were occurring beyond the motion-activation range. To double-check, I used my phone app to view the other two Stick-up Cams, and they both still had the "30-seconds" interval option for Snapshot ... BUT then on one of these cams, I toggled from the "30-seconds" to "5 minutes" option and it switched fine, but now the "30-seconds" option disappearred and hasn't returned! The last of the 3 Stick-up Cams is still on "30-seconds" and I don't dare change that selection! So, I have 2 Cams taking Snaps at 5 long minute intervals, with 1 cam still at every 30-seconds. What happened?

As a follow-on to my comment above ..... I now know what happened. I’m excited! My “30 Seconds" interval Snapshot option is back! I don’t know what actually caused the original loss of the “30 Second” option. It could have been something to do with a Firmware update, or a glitch during a download, or the alignment of the stars with Jupiter and Mars. But now all three of my outdoor Stick-up Plug-In cameras (Gen 2) have new Snapshot interval choices of: - Every 3 Minutes. - Every 1 Minute. - Every 30 Seconds. When I did my original installation of my Stick-up cams, the instructions had me choose between Plug-in power or Battery power. Mine are all Plug-in powered. In each Stick-up cam there is an internal compartment for a click-in battery. Mine are empty. After setting up as a “Plug-In” device, all three cams had the following 4 choices available for Snapshot intervals: - Every 30-Seconds. - Every 1 Hour. - Every 14 Minutes - Every 5 Minutes. After a few weeks, one Stick-up cam needed a full, hard, “Factory Reset” to correct a problem. That’s when the first camera lost the “Every 30 second” option, and I was left with only the 3 options of “1 Hour”, “14 Minutes”, and the “5 Minutes”. Shortly afterwards, another Stick-up cam also lost the “30 Second” option, and it was never “Hard Reset” nor had a ‘soft’ reset procedure. With all three of my cams, **both** before and after the interval loss, the “Device Health” indicated everything was fine. The “Power Source” displayed “Power Outlet” (not “Battery”). All other “Device Health” indications were good too. I kept searching for a solution to get “30 Seconds” back, to no avail. Today, I checked “Device Setting”, and then found and selected “General Settings.” To my surprise it displayed “Power Mode - Battery.” Huh? I’m not sure, but it used to show “Plug-in” or something like that. Now it was different and had switched to a Battery Mode. Took me awhile to realize I could click on “Power Mode” to arrive at another sub-set menu … showing “Battery Mode” and “Wired Mode” with a blue bar icon at the bottom of the screen to transfer back & forth between the two power modes! But it now makes sense, why I lost the “30 Seconds” and eventually ended up with only the 3 interval selections. Stick-up camera’s power source can be either Battery or Plug-In. Lots of repetitive Snapshots can put a high drain on the battery if interval choice is very short. My cam mistakenly believed it was Battery powered (even though there is not even a battery in the compartment). Selecting the “Switch to Wire Mode” blue bar, another setup process attempted to start. Apparently, the camera’s Blue light was supposed to start blinking … never did … and the process had to be initiated by pressing the cam’s Orange reset button. This was not a hard reset, but rather a momentary push on the Orange button for a soft reset. It turns out that all 3 of my Stick-up cams needed the Orange reset button pressed to initiate the setup. Now with a completed soft reset, all three of my outdoor Stick-up Plug-In cameras show “Power Mode – Wired.” They all have 3 new, significantly shorter Snapshot interval options of: - Every 3 Minutes. - Every 1 Minute. - Every 30 Seconds. I discovered that some of my previous selections had remained unchanged during this soft reset. But some did change back to factory default settings, such as Alert-sounds. Also, some previous features were gone, and several new features were added. A totally new “Motion Zones” format (just like those found on Ring Indoor Cameras) allows you to move 8 blue dots to create a tailored, geometric-shaped zone. I apologize for thinking Ring intentionally stole away my favorite “30 Second” interval. And whoever was involved in the latest firmware that permits “Wired-Powered” Stick-up (Gen 2) cameras to have short intervals . . . Thank You! Two things I still find bizarre. How did my Stick-Up Plug-In originally have **4** interval choices? And how did the camera change the power mode to battery? Bottomline, I can again select “30 Seconds” and I’m happy! What would make me ecstatic? Provide new firmware for my hardwired powered, Ring Video Door 2 with a Snapshot interval shorter than its current minimum of “5 Minutes.” Yes? Maybe? Soon? ?

The time options \> One hour, 14 minutes and 5 minutes, I have to ask the question why 14 minutes seems very odd, would prefer 30 minutes to be added to this time option or make it completely variable by the user....

Good evening, while i am happy with my ring devices can you please explain why i now have 15 min snap shots on my battery doorbell and not the 5 mins i used to have in order to conserve the battery and the only way i can have 5 mins is by mains powering or solar powering my door bell which is an added expense to myself when the products are already on the pricey side..If it means i need to charge my doorbell more often to have the setting I want and not somebody else then so be it..Id really like,and im sure others will also like to have the 5 mins back and to be able to control my device how I want to or i might have to move to a different range of devices....many thanks Paul